90° Square Shoulder End Mills & Shell Mills

Square Shoulder End Mills

("C" denotes coolant thru tool)

NEW: 1.25" cutters and smaller are available without weldon flats in limited supplies. Add WOF to end of part number when ordering.

Square Shoulder End Mill
End Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Shank Dia.
(d2)		 Overall Length
(l1)		 Effective Length
(l2)		 Inserts
.500" SSEM0500-0625-R35-1 .350" 1 .625" 2.75" .97" APET1003.. / XPET1003..
.625" SSEM0625-0625-R35-2 .350" 2 .625" 3.00" 1.09" APET1003.. / XPET1003..
.750" SSEM0750-0750-R35-2 .350" 2 .750" 3.50" 1.47" APET1003.. / XPET1003..
.750" SSEM0750-0750-R35-2C .350" 2 .750" 3.50" 1.47" APET1003.. / XPET1003..
.750" SSEM0750-0750-R35-3 .350" 3 .750" 3.50" 1.47" APET1003.. / XPET1003..
.625" SSEM0625-0750-R55-1 .550" 1 .750" 3.35" 1.15" APET1604.. / XPET1604..
.750" SSEM0750-0750-R55-1 .550" 1 .750" 3.49" 1.40" APET1604.. / XPET1604..
1.000" SSEM1000-0750-R35-4 .350" 4 .750" 3.50" 1.47" APET1003.. / XPET1003..
1.000" SSEM1000-1000-R35-3C .350" 3 1.000" 4.00" 1.72" APET1003.. / XPET1003..
1.000" SSEM1000-1000-R55-2 .550" 2 1.000" 4.28" 2.00" APET1604.. / XPET1604..
1.000" SSEM1000-1000-R55-2C .550" 2 1.000" 4.28" 2.00" APET1604.. / XPET1604..
1.000" SSEM1000-1000-R55-2LC .550" 2 1.000" 5.28" 3.00" APET1604.. / XPET1604..
1.250" SSEM1250-1250-R35-5C .350" 5 1.250" 4.00" 2.50" APET1003.. / XPET1003..
1.250" SSEM1250-1250-R55-3 .550" 3 1.250" 4.00" 2.50" APET1604.. / XPET1604..
1.250" SSEM1250-1250-R55-3C .550" 3 1.250" 4.00" 2.50" APET1604.. / XPET1604..
1.500" SSEM1500-1250-R55-3 .550" 3 1.250" 4.40" 2.50" APET1604.. / XPET1604..
1.500" SSEM1500-1250-R55-4 .550" 4 1.250" 4.40" 2.50" APET1604.. / XPET1604..
1.500" SSEM1500-1250-R55-4C .550" 4 1.250" 4.40" 2.50" APET1604.. / XPET1604..

Square Shoulder Extended Reach End Mills

("C" denotes coolant thru tool)

Square Shoulder Extended Reach End Mill
Extended Reach End Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Shank Dia.
(d2)		 Overall Length
(l1)		 Effective Length
(l2)		 Inserts
.500" SSER0500-2000-R35-1 .350" 1 .625" 3.91" 2.00" APET1003.. / XPET1003..
.625" SSER0625-2500-R35-2C .350" 2 .750" 4.41" 2.50" APET1003.. / XPET1003..
.750" SSER0750-2500-R35-2C .350" 2 1.000" 4.78" 2.50" APET1003.. / XPET1003..
.750" SSER0750-4000-R35-2C .350" 2 1.000" 6.28" 4.00" APET1003.. / XPET1003..
1.000" SSER1000-4000-R55-2C .550" 2 1.250" 6.28" 4.00" APET1604.. / XPET1604..
1.000" SSER1000-6000-R55-2C .550" 2 1.250" 8.28" 6.00" APET1604.. / XPET1604..
1.250" SSER1250-4000-R55-3C .550" 3 1.250" 6.28" 4.00" APET1604.. / XPET1604..
1.500" SSER1500-4000-R55-3C .550" 3 1.500" 6.69" 4.00" APET1604.. / XPET1604..

Square Shoulder Extended Reach End Mills with Carbide Core

Carbide Core Extended Reach End MillDAPRA is transitioning from 3-flute to 2-flute tools.
Carbide Core Extended Reach End Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Shank Dia.
(d2)		 Overall Length
(l1)		 Effective Length
(l2)		 Inserts
.750" CC-SSER0750-2500-R35-2 .350" 2 1.000" 4.78" 2.50" APET1003.. / XPET1003..
.750" CC-SSER0750-4000-R35-2 .350" 2 1.000" 6.28" 4.00" APET1003.. / XPET1003..
1.000" CC-SSER1000-4000-R55-2 .550" 2 1.250" 6.28" 4.00" APET1604.. / XPET1604..
1.000" CC-SSER1000-6000-R55-2 .550" 2 1.250" 8.28" 6.00" APET1604.. / XPET1604..
1.000" CC-SSER1000-8000-R55-2 .550" 2 1.250" 10.28" 8.00" APET1604.. / XPET1604..
1.250" CC-SSER1250-3200-R55-3 .550" 3 1.250" 5.50" 2.62" APET1604.. / XPET1604..
1.250" CC-SSER1250-4000-R55-3 .550" 3 1.250" 6.28" 4.00" APET1604.. / XPET1604..
NEW 1.250" CC-SSER1250-6000-R55-2 .550" 2 1.500" 8.69" 6.00" APET1604.. / XPET1604..
NEW 1.250" CC-SSER1250-8000-R55-2 .550" 2 1.500" 10.69" 8.00" APET1604.. / XPET1604..
1.250" CC-SSER1250-6000-R55-3 .550" 3 1.250" 9.25" 6.00" APET1604.. / XPET1604..
NEW1.500" CC-SSER1500-6000-R55-2 .550" 2 1.500" 8.69" 6.00" APET1604.. / XPET1604..
1.500" CC-SSER1500-6000-R55-3 .550" 3 1.500" 8.69" 6.00" APET1604.. / XPET1604..

Square Shoulder Shell Mills

Square Shoulder Shell Mill
Standard Pitch Shell Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Arbor Dia.
(d2)		 Overall Height
(h)		 Counter Bore
(l)		 Inserts
1.500" SSSM1500-0750-R55-4 .550" 4 .750" 1.75" .58" APET..1604 / XPET1604..
2.000" SSSM2000-0750-R55-4 .550" 4 .750" 1.50" .60" APET..1604 / XPET1604..
2.000" SSSM2000-0750-R55-5 .550" 5 .750" 1.50" .60" APET..1604 / XPET1604..
2.500" SSSM2500-1000-R55-5 .550" 5 1.000" 1.50" .80" APET..1604 / XPET1604..
3.000" SSSM3000-1000-R55-6 .550" 6 1.000" 2.00" .80" APET..1604 / XPET1604..
4.000" SSSM4000-1500-R55-8 .550" 8 1.500" 2.00" 1.90" APET..1604 / XPET1604..
5.000" SSSM5000-1500-R55-8 .550" 8 1.500" 2.00" 2.10" APET..1604 / XPET1604..
6.000" SSSM6000-1500-R55-10 .550" 10 1.500" 2.00" 2.10" APET..1604 / XPET1604..
6.000" SSSM6000-2000-R55-7 .550" 7 2.000" 2.00" 2.75" APET..1604 / XPET1604..
8.000" SSSM8000-FM-R55-9 .550" 9 2.500" 2.50" 4.00" BC APET..1604 / XPET1604..
Coarse Pitch Shell Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Arbor Dia.
(d2)		 Overall Height
(h)		 Counter Bore
(l)		 Inserts
2.000" SSSM2000-0750-R55-3 .550" 3 .750" 1.50" .60" APET..1604 / XPET1604..
3.000" SSSM3000-1000-R55-3 .550" 3 1.000" 2.00" .80" APET..1604 / XPET1604..

Helical Roughing End Mills

Helical Roughing End Mill
Helical Roughing End Mills
Cutting Dia.
(D)		 Holder Depth of Cut Flutes Shank Dia.
(d2)		 Overall Length
(l1)		 Effective Length
(l2)		 No. of Inserts Inserts
1.000" HREM1000-1000-R2-120 1.200" 2 1.000" 4.50" 2.04" 8 APET..1003 / XPET1003..
1.250" HREM1250-1250-R2-165 1.650" 2 1.250" 4.88" 2.40" 6 APET..1604 / XPET1604..
1.500" HREM1500-1250-R3-215 2.150" 3 1.250" 5.65" 3.15" 12 APET..1604 / XPET1604..
40mm HREM40mm-1250-R2-165 1.650" 2 1.250" 4.80" 2.44" 6 APET..1604 / XPET1604..

Helical ("stacked") cutters create much more tool pressure than standard end mills, due to the increased number of engaged inserts. Dapra recommends not exceeding 10% of the tool diameter in width of cut (WOC) with these HREM tools; irreversible cutter damage may occur. It is recommended that the more positive XPET insert geometry be used with Helical Roughing End Mills.

Utility Cutters

Make the most of your APET and XPET Inserts!

BCSM shell mills allow the unused corner of the APET/XPET inserts to be used for general face milling - this means you get 4 usable edges per insert instead of 2!

CMEM end mills are perfect for chamfer milling, providing a free-cutting positive geometry for both 30° and 45° chamfering.

Back Corner Shell Mills
15° Back Corner Shell Mills (BCSM)
Cutting Dia.
(D)		 Holder Depth of Cut Flutes OD Arbor Dia.
(d2)		 Overall Heigh
(h)		 Counter Bore
(l)		 Inserts
2.000" BCSM2000-0750-R35-4 .250" 4 2.11" .750" 1.50" .60" APET1003.. / XPET1003..
2.000" BCSM2000-0750-R55-4 .375" 4 2.16" .750" 1.50" .60" APET1604.. / XPET1604..
3.000" BCSM3000-1000-R55-5 .375" 5 3.16" 1.000" 2.00" .80" APET1604.. / XPET1604..
Chamfering End Mills
Chamfering End Mills (CMEM)
Cutting Dia.
(D)		 Holder Depth of Cut Flutes OD Shank Dia.
(d2)		 Overall Length
(l1)		 Effective Length
(l2)		 A Inserts
.500" CMEM0500-30-R35-2 .300" 2 .80" .750" 3.00" 1.45" 30° APET1003.. / XPET1003..
.500" CMEM0500-45-R35-2 .245" 2 .94" .750" 3.50" 1.45" 45° APET1003.. / XPET1003..
.625" CMEM0625-45-R55-2 .245" 2 1.40" .750" 3.50" 1.45" 45° APET1604.. / XPET1604..
.700" CMEM0700-30-R55-2 .475" 2 1.25" .750" 3.50" 1.45" 30° APET1604.. / XPET1604..
.750" CMEM0750-30-R35-3 .300" 3 1.05" .750" 3.50" 1.45" 30° APET1003.. / XPET1003..
.750" CMEM0750-45-R35-3 .245" 3 1.18" .750" 3.50" 1.45" 45° APET1003.. / XPET1003..
1.000" CMEM1000-30-R55-3 .475" 3 1.53" 1.000" 4.00" 1.72" 30° APET1604.. / XPET1604..
1.000" CMEM1000-45-R55-3 .390" 3 1.76" 1.000" 4.00" 1.72" 45° APET1604.. / XPET1604..

Screw-On Modular Heads

Dapra's line of screw-on heads fits industry standard cutting systems:

  • Compatible with ISO standard modular cutting systems
  • Close-tolerance mounting of heads minimizes runout and maximizes rigidity
  • Provide significantly more effective reach than solid end mills
  • Use standard inch wrench flats, no special metric wrenches needed
Screw-On Modular Tool HeadNEW=*, Available Soon=diamond
 
Square Shoulder Screw-On Heads
Dia. Holder M DOC E Flutes Inserts Open-End Wrench
.750" SSEM0750-MOD-R35-2 M10 .350" 1.50" 2 APET1003.. / XPET1003.. 9/16"
1.000" SSEM1000-MOD-R55-2 M12 .550" 1.50" 2 APET1604.. / XPET1604.. 11/16"
1.250" SSEM1250-MOD-R55-2 M16 .550" 1.75" 2 APET1604.. / XPET1604.. 15/16"
1.250" SSEM1250-MOD-R55-3 M16 .550" 1.75" 3 APET1604.. / XPET1604.. 15/16"
1.500" SSEM1500-MOD-R55-2 M16 .550" 1.75" 2 APET1604.. / XPET1604.. 15/16"
1.500" SSEM1500-MOD-R55-3 M16 .550" 1.75" 3 APET1604.. / XPET1604.. 15/16"

Modular Extensions

Dapra's modular extensions provide even more cutting options:

  • Made of high-density tungsten, providing extra resistance to deflection and chatter
  • Machined on both ends; can be cut in half and used with two different modular heads
  • Metric shank diameter provides clearance for each inch size modular head
Modular Extension
Modular Extensions
For Head Diameter Modular Extensions OAL Shank Diameter (S)
.750" ME-0750-18MM-900 9" 18mm
1.000" ME-1000-25MM-1100 11" 25mm
1.250" ME-125/150-25MM-1200 12" 25mm
1.500" ME-125/150-25MM-1200 12" 25mm
Click here for information on our NEW Carbide Core Modular Extensions

Dapra 90° Square Shoulder products are made in the USA.